BUILT MOTOR? Discussion. READ
10-11-2009, 07:07 AM
#151
Registered Member
Join Date: Oct 2009
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Re: BUILT MOTOR? Discussion. READ
sorry to be brutally honest, but you are pretty illiterate. You should probably take a 9th grade english class again.
on a side note, not saying rep even matters, but seeing that i have more than both of yall, i obviously have adding to conversations a little more than you.
on a side note, not saying rep even matters, but seeing that i have more than both of yall, i obviously have adding to conversations a little more than you.
Last edited by eightrac; 10-11-2009 at 07:10 AM.
10-11-2009, 07:09 AM
#152
Registered Member
Join Date: Oct 2009
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
10-11-2009, 07:43 AM
#153
nortaP
Join Date: Feb 2009
Posts: 13,272
Likes: 0
Received 0 Likes
on
0 Posts
Re: BUILT MOTOR? Discussion. READ
10-11-2009, 10:42 AM
#154
wadafuxup
Join Date: Apr 2008
Location: York County, VA
Posts: 1,758
Likes: 0
Received 0 Likes
on
0 Posts
10-11-2009, 11:30 AM
#155
Boost is Better
Join Date: Oct 2004
Location: Richmond area
Posts: 2,456
Likes: 0
Received 0 Likes
on
0 Posts
Re: BUILT MOTOR? Discussion. READ
Dude you were in one of the threads bitching about a built motor that I was looking at. While THAT one may not have been a "built motor" by any means your description was well over what could be described as "built".
Like I stated in that thread that you came in and bashed up was this
Yes people do use the term too loosely sometimes but there is always a different definition between different people.
I've used the term "FULLY built" before but then reiterated that it wasn't sleeved.
SO... in your terms what should I call that?
If I have
cams
springs
retainers
port
polish
Pistons
rings
rods (H beam) or rather fuck it even if I had aftermarket I beams
bearings
STOCK crank but knife edged and balanced rotating assy to 10,000rpm
cam gears
fuel rail
and ill stop there because to ME
thats built cuz it damn sure aint stock??
May not be fully built at this point but it is built.
My teal hatch I just sold was a "built" motor and put down 415hp and 270ft lb of tourge at 15.55psi TO THE WHEELS and you don't want me to call that built? what is it then.
Like I stated in that thread that you came in and bashed up was this
Yes people do use the term too loosely sometimes but there is always a different definition between different people.
I've used the term "FULLY built" before but then reiterated that it wasn't sleeved.
SO... in your terms what should I call that?
If I have
cams
springs
retainers
port
polish
Pistons
rings
rods (H beam) or rather fuck it even if I had aftermarket I beams
bearings
STOCK crank but knife edged and balanced rotating assy to 10,000rpm
cam gears
fuel rail
and ill stop there because to ME
thats built cuz it damn sure aint stock??
May not be fully built at this point but it is built.
My teal hatch I just sold was a "built" motor and put down 415hp and 270ft lb of tourge at 15.55psi TO THE WHEELS and you don't want me to call that built? what is it then.
Thread
Thread Starter
Forum
Replies
Last Post