DazedandConfuse

Hey guys, I've been on the miata forums for a few years but never the local forum here. DazedandConfused, Prequel2theSequel, and Blumpkinsgalore are my usernames on the other forums in case anyone is on them. I sometimes go to the Cars and Coffee in Va Beach and Williamsburg, so hope to get to know you guys.

Heres specs on my car: 2004 Mazdaspeed Miata

Rolling on:
BC Racing Coilovers
3.9 ratio steering rack
16x8 et0 XXR 002 powdercoated black
205/40 Dunlop DZ101 all around
Neo Chro lugnuts
DBA slotted rotors
Axxis ULT pads
custom cut knuckles

Exterior:
Autokonexion duckbill version 1 trunk with 3rd brakelight delete
OEM hardtop with spec miata plates
NB2 small sideskirts
NB2 front bumper
Chaser Scoote 2 fiberglass hood
Strobelights inside both tail and headlights
35w 6k HIDs
Bright LED license plate lights
NACA duct vents in quarter windows

Interior:
Replica Bride Vios III (lowmax) black with custom seat mount
Ebay deep dish steering wheel
NRG Quick Release v2.5 and short hub
Works Bell 25mm hub spacer
Purple bubbly dildo shiftknob
KSport hydraulic ebrake w/ hardlines
Purple LED strip interior lights.
Bright LED dome lights
radio, speaker, center console, and rear panels/carpet delete
Cusco Safety-21 rollcage
Stewart Warner boost guage

Engine and Drivetrain:
Begi throttle inlet pipe
Begi cold air box, intake, and intercooler piping
Flyin Miata catless downpipe
Turbosmart Dualport BOV
Manual boost controller set to 10lbs
Ebay front mount intercooler
Mazdaspeed Motormounts
949racing twindisk clutch w/7lb flywheel
3.9 TorsenII differential and rear end swap

Items waiting to be installed when I find time:
Koyo 55mm aluminum radiator
Flying Miata stage 2 airflow kit (dual spal fans and aluminum radiator shroud)
Hydra Nemesis 2.6 ecu with 550cc injectors
Replica Bride Vios III passenger seat
Garage Vary carbon fiber top radiator shroud
Garage Vary carbon fiber NB2 eyelids
3" turndown pipe to replace muffler.

Future plans:
Autokonexion kevlar widebody kit
Warhouse Performance carbon fiber fastback
Warhouse Performance carbon fiber extractor hood
ArTech manifold, 3" exhaust (w/blast pipes), and intercooler piping
Garrett 2871 at 15lbs
Tial BOV and external wastegate with open dump pipe
Built engine w/ 8500rpm rev limit (turn up boost to 25lbs once this is installed)
More guages
Aluminum or carbon fiber door cards
17x10 low offset rims to fill the kit

and now that I've blabbed on long enough about my car...........here are some recent pics

Dillweed

Welcome to the forum!

RE-SPECGARAGE

not bad...pleanty of slammed miatas in the area

DazedandConfuse

I havn't seen too many. Maybe only 2 others. I would like to meet other slammed miata guys. I still have some work to do whenever I get to have some free time at home to make my ride look a little better while I wait for the widebody kit in the mail.

New headlights, get rid of bumper gap, and fix hood skeleton so it doesnt hit my cold air box. Also tape back on my driver side sideskirt. Once the kit comes in, I'll purchase the fastback and get everything put together and a whole new paintjob to make the car shine xD

by the way. my name is seth

And2TheRepublic

Welcome.

Kyle!

lose/paint the hood and you can touch my dak, if not.. you can touch your own

Welcome

DazedandConfuse

No need to paint the hood yet when I will just paint the car another color soon enough. Waiting for my other body parts to arrive before I paint anything.

Kyle!

Are you a doctor?

DazedandConfuse

I'm guessing you don't watch Metalocalypse. I've decided to name things in my family after members of Dethklock.
Parents cat = murderface
My cat and sisters cat = skwisgaar and toki
my car = dr. rockso

The rock and roll clown that is addicted to cocaine

L_U_C_K

Welcome!