Bulkhead rear section "FAB"
#1
Danny@respecgarage
Thread Starter
Join Date: Aug 2005
Location: www.respecgarage.com
Posts: 4,471
Likes: 0
Received 0 Likes
on
0 Posts
Bulkhead rear section "FAB"
Im trying to find more information in what would be the correct way to build a buklhead to separate the rear and the drivers compartment. it does not need to include a window but it would be nice to have. I will be adding a fuel cell and battery relocation to the rear part of the hatch.
Im thinking something alont the lines of this.
Revolution Rx7
Im thinking something alont the lines of this.
Revolution Rx7
#2
Dickbutt #peentip
Join Date: Jan 2007
Location: Virginia Beach
Posts: 10,256
Likes: 0
Received 0 Likes
on
0 Posts
Re: Bulkhead rear section "FAB"
Depends on what the rule books say. I believe you have to be 100% separated if there's fuel back there.
you must design something that you can remove, or get access through.
Also, that car is busy as fuck back there
you must design something that you can remove, or get access through.
Also, that car is busy as fuck back there
#3
Danny@respecgarage
Thread Starter
Join Date: Aug 2005
Location: www.respecgarage.com
Posts: 4,471
Likes: 0
Received 0 Likes
on
0 Posts
Re: Bulkhead rear section "FAB"
that car is a time attack beast. The only thing the rule books state is that a fuel cell has to be seperated 100% from the drivers compartment. Reason why i want to do a bulkhead is to have access to everything in the rear section of the car and keep all hazards away from me. Right now im just trying to gather info on this. I havent read thru the NASA rule book yet on this topic.
#4
The only thing I could possibly think about doing this is meet the requirements to what regulation you're driving in. I'm sure the way you set it up doesn't matter as long as you meet code.
The bulkhead in the revolution rx7 is center biased so it gives the car a better center of gravity, I would think building everything over the rear axle would help balance for drifting better. I read a big article about the revolution rx7 somewhere ill see if I can't dig it up for you.
Edit:
http://www.motoiq.com/magazine_articles/id/2311/garage-revolutions-time-attack-fd3s-rx-7-part-1.aspx
You may have already read this but I thought it was a good write up about the car
The bulkhead in the revolution rx7 is center biased so it gives the car a better center of gravity, I would think building everything over the rear axle would help balance for drifting better. I read a big article about the revolution rx7 somewhere ill see if I can't dig it up for you.
Edit:
http://www.motoiq.com/magazine_articles/id/2311/garage-revolutions-time-attack-fd3s-rx-7-part-1.aspx
You may have already read this but I thought it was a good write up about the car
Last edited by Yep4doors; 12-07-2012 at 12:55 AM.
#5
Racetracks
Join Date: Nov 2002
Location: How long is a piece of string?
Posts: 15,668
Likes: 0
Received 0 Likes
on
0 Posts
Re: Bulkhead rear section "FAB"
Check the rules and see how complete the bulkhead has to be and what materials are acceptable if fire protection is necessary, etc., and this will likely tell you if a window can be added and what window materials are acceptable too.
If you can, it would be nice to attach mount points to the body and then make the bulkhead mount to those points, instead of having to make the bulkhead into a structural member or worry about what happens when the body twists. If you just take a piece of light gauge sheet metal and fold the edges and weld it to the body in a whole bunch of places, bad things will happen and you'll likely end up with a wrinkly piece of metal.
If you can, it would be nice to attach mount points to the body and then make the bulkhead mount to those points, instead of having to make the bulkhead into a structural member or worry about what happens when the body twists. If you just take a piece of light gauge sheet metal and fold the edges and weld it to the body in a whole bunch of places, bad things will happen and you'll likely end up with a wrinkly piece of metal.
#6
Check the rules and see how complete the bulkhead has to be and what materials are acceptable if fire protection is necessary, etc., and this will likely tell you if a window can be added and what window materials are acceptable too.
If you can, it would be nice to attach mount points to the body and then make the bulkhead mount to those points, instead of having to make the bulkhead into a structural member or worry about what happens when the body twists. If you just take a piece of light gauge sheet metal and fold the edges and weld it to the body in a whole bunch of places, bad things will happen and you'll likely end up with a wrinkly piece of metal.
If you can, it would be nice to attach mount points to the body and then make the bulkhead mount to those points, instead of having to make the bulkhead into a structural member or worry about what happens when the body twists. If you just take a piece of light gauge sheet metal and fold the edges and weld it to the body in a whole bunch of places, bad things will happen and you'll likely end up with a wrinkly piece of metal.
Although I didn't think about the integrity of the metal warping