What Wheel Spacer size (trying to go flush)
#11
I Love to Hate
Join Date: Mar 2006
Location: Va Beach
Posts: 6,777
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Wheel Spacer size (trying to go flush)
you have so many numbers everywhere i have no urge to try.
front wheel specs: xxxxxx
rear wheel specs: xxxxxx
what you want fronts to be: xxxxx
what you want rears to be: xxxxxx
front wheel specs: xxxxxx
rear wheel specs: xxxxxx
what you want fronts to be: xxxxx
what you want rears to be: xxxxxx
#12
Re: What Wheel Spacer size (trying to go flush)
Front and rear is 17x7 et40. Fronts are sucked in 1inch. Rear are sucked in 2 inches.
I want 17x8.5 et56 on front and flush.
I want 17x9.5 et56 on rear and flush.
This is hard to explain with out actually seeing how my wheels currently fit. They are sunk in like a bitch.
I want 17x8.5 et56 on front and flush.
I want 17x9.5 et56 on rear and flush.
This is hard to explain with out actually seeing how my wheels currently fit. They are sunk in like a bitch.
#13
I Love to Hate
Join Date: Mar 2006
Location: Va Beach
Posts: 6,777
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Wheel Spacer size (trying to go flush)
Front and rear is 17x7 et40. Fronts are sucked in 1inch. Rear are sucked in 2 inches.
I want 17x8.5 et56 on front and flush.
I want 17x9.5 et56 on rear and flush.
This is hard to explain with out actually seeing how my wheels currently fit. They are sunk in like a bitch.
I want 17x8.5 et56 on front and flush.
I want 17x9.5 et56 on rear and flush.
This is hard to explain with out actually seeing how my wheels currently fit. They are sunk in like a bitch.
the 17x8.5+56 will only take away 3mm of the fender to tire sunkenness
and the rear 17x9.5+56 will clean up 16mm of the gap
Last edited by B-Well; 07-14-2009 at 07:44 PM.
#16
I Love to Hate
Join Date: Mar 2006
Location: Va Beach
Posts: 6,777
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Wheel Spacer size (trying to go flush)
i think this thread is worthless,
you have the wheels you want,
you know the gap that needs to be filled,
even have the measurements of said gaps,
buy spacers to fill the gap!
25.4mm front and 33.5mm rear, or just buy them in sae
1" front 1.25 rear.
Care to tip me off on the necessity of this thread?
#17
Re: What Wheel Spacer size (trying to go flush)
I wanted to verify I calculated it right before buying a nonreturnable item. Otherwise yes. This thread is now worthless.
However in a week I will be asking about what tire size. But that will have more measurements and pictures.
However in a week I will be asking about what tire size. But that will have more measurements and pictures.
Last edited by Harold_Fastwake; 07-14-2009 at 08:04 PM.
#18
I Love to Hate
Join Date: Mar 2006
Location: Va Beach
Posts: 6,777
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Wheel Spacer size (trying to go flush)
if you are trying to make the sawblades fit like they 17x7s did you will need to have the hub of the wheels shaved as the new set pokes more than the 17x7 without any spacers.
#19
Re: What Wheel Spacer size (trying to go flush)
Are you asking me if I want my 9.5s to be sunk in like my 7s?
I want the exact opposite. I wanted to figure out what spacer I needed to make my wheels sit flush.
#20
I Love to Hate
Join Date: Mar 2006
Location: Va Beach
Posts: 6,777
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Wheel Spacer size (trying to go flush)
you have so many numbers everywhere i have no urge to try.
front wheel specs(the wheels you are going to be running and want to get spacers for to make them fit better, width and offset): xxxxxx
rear wheel specs(the wheels you are going to be running and want to get spacers for to make them fit better, width and offset): xxxxxx
what you want fronts to be(another set of wheels you have seen on the same car you have and fit the car very well, width and offset): xxxxx
what you want rears to be(another set of wheels you have seen on the same car you have and fit the car very well, width and offset): xxxxxx
front wheel specs(the wheels you are going to be running and want to get spacers for to make them fit better, width and offset): xxxxxx
rear wheel specs(the wheels you are going to be running and want to get spacers for to make them fit better, width and offset): xxxxxx
what you want fronts to be(another set of wheels you have seen on the same car you have and fit the car very well, width and offset): xxxxx
what you want rears to be(another set of wheels you have seen on the same car you have and fit the car very well, width and offset): xxxxxx